Multibond EZ-2 Wood Glue

64112718,9l/20kg1152,86 €

Multibond EZ-2 - Wood Glue

Multibond EZ-2 is a one-part crosslinking polyvinyl acetate emulsion adhesive developed with a low minimum use temperature for use in a wide variety of plant conditions. Multibond EZ-2 meets DIN EN204 D3 as well as ASTM D-5572 dry use for finger joints in non-structural lumber products.


  • Excellent for finger jointing or cold press laminating in colder climates;
  • Light colored glue line;
  • Water-resistant;
  • Low minimum use temperature (+7°C);


  • Meets requirements for HPVA/ANSI EF 2009
  • Meets WDMA Type 1 and 2 water resistance
  • Meets European Standard DIN EN204 D3
  • Meets DIN EN 14257 WATT 91 Heat Testing
  • Meets ASTM D-5572-99 Dry Use
  • 175.105 FDA Compliant

DIN EN 204 D3 Classification of Thermoplastic Wood Adhesives for Non-structural Applications:  
Load group D3 Beech

Storage sequence Minimum required average value (N/mm2) Average value (N/mm2) on Multibond EZ-2
1 ≥ 10 15,5
3 ≥ 2 2,2
4 ≥ 8 13,5

*Rosenheim report 505 36441/3e 8/72008

DIN EN 14257 (WATT 91)

Average value (N/mm2) on Multibond EZ-2

*Rosenheim report 505 36441/4e 8/7/2008

ASTM D-5572-99 Dry Use for fingerjoints in non-structural Lumber Products

Multibond EZ-2 Test results
Exposure Strength Average
Wood failure Minimum
Wood failure Average
Wood failure Minimum
Dry 450 - 100 100
3 cycle soak 373 - 98 95
Elevated Temp. 289 - - -
Exposure Strength Average
Strength Minimum
Wood failure Average
Wood failure Minimum
Dry 141 - 60 30
3 cycle soak 70 - 30 15
Elevated Temp. 70 - - -

*Teco test report #01-114 Ponderosa Pine


Chemical family description: Crosslinking polyvinyl acetate emulsion adhesive
Color: Light yellow /cream colored liquid
Weight solids (%): 45.5 - 48.5%
2,3 – 3,3
Typical viscosity mPas:
2500 - 4000 (3/12/28°C)
Specific gravity:
Freeze/thaw Stability:
Minimum Required Spread:
170 – 250 g/m2

Suggested minimum use temperature:: +7°C
Open Assembly Time: 5 min. (21°C./50%RH)
Total Assembly Time: 15 min. (21°C./50%RH)

Required Clamping Pressure:
Low density species (Pine, Poplar) – 7-10kg./,
Medium density species (Rubberwood, Cherry) – 9-13 kg./,
Hi dedsity speciesi (Oak, Maple) 13-18 kg./

Clean-up: For easy removal of adhesive from equipment, clean up while it is still wet with warm water (this includes the glue roller and pans). For dried glue, steam and or hot water are the most effective. Using glue release agents on equipment will also allow for easier clean up.

IMPORTANT NOTICE TO CUSTOMER: The recommendations and data contained in this Product Data Sheet for use of this product are based on information Franklin believes to be reliable. They are offered in good faith without guarantee, as conditions and methods of use of our product by Customer are beyond Franklin’s control. Customer must determine the suitability of the product for a particular application before adopting it on a commercial scale. Discoloration and checking of wood veneer materials may occur with use of the product. These occurrences range in appearance, color and may also vary depending upon the species of wood veneer to which the product is applied. Such discoloration and checking may appear during or after the manufacturing process which utilizes the product. Environmental conditions in some manufacturing plants and end-use locations can contribute to discoloration and checking. Because such discoloration and checking are attributable to conditions beyond Franklin’s control, Franklin cannot assume any responsibility or liability for any discoloration and/or checking problems that might occur. All orders for Franklin products shall be subject to Franklin International, Inc.’s Standard Terms and Conditions of Sale which may be found at (“Standard Terms”). Different or additional terms proposed by Customer are expressly rejected and shall not become part of the agreement between Customer and Franklin International, Inc. with respect to any order. Contact Franklin International, Inc. immediately if you cannot access our Standard Terms and we will provide you a copy upon request. Any sale of products by Franklin to Customer is expressly conditional upon Customer’s consent to the Standard Terms, and Customer’s acceptance of any performance by, or receipt of products from, Franklin International, Inc. shall constitute Customer’s acceptance of the Standard Terms and Conditions of Sale. © Copyright 2015. All rights reserved. Franklin International. Revised 08/24/15.